We are collapsing two aggregation rows onto FortiSwitch, and the last piece is a 25G interconnect between an FS2048 and an FS648 in adjacent racks. Everything else in the design came up on the first attempt; this one link refuses to. FortiSwitch 2048, 25G front-panel port FortiSwitch 648, 25G…
Four HP A5500-HI switches in an IRF stack logged unsupported transceiver messages for six rear-module (JD368B) ports that were cabled with HP J9281B SFP+ DACs to ProLiant Gen8 servers with 530SFP+ NICs. display transceiver interface shwed Transceiver Type STACKSFPPLUS, Connector COPPER, Vendor Name…
Small home rack, one server and one switch. I replaced an XGS1250-12 with an XS1930-10 and the only thing that did not survive the swap is the server uplink. Zyxel XS1930-10, SFP+ port with media type set to DAC10G Asus XG-C100F in the server 10Gtek CAB-10GSFP-P5M, 5 m passive twinax, AWG26 a…
Setting up 10G between a server and a TP-Link switch, nothing exotic. The card shows up in the system, driver loads normally, but there's no link on the port at all - no errors, no negotiation attempts. server: Intel X710, four 10GbE SFP+ ports, firmware 9.140.76856 TP-Link switch, SFP+ port cable…
My firewall is a Supermicro E300-9A running pfSense Plus 22.05, and both 10G SFP+ ports refuse to come up. Neither ix2 nor ix3 ever shows carrier, whatever I put in the cage. Hardware: Supermicro E300-9A, pfSense Plus 22.05 Ubiquiti DAC-SFP10-0.5M and a 10Gtek passive twinax cable Supermicro…
The poster wanted to connetc Aruba 2540 switches (JL357A, firmware YC.16.09.0001) to Cisco Catalyst 9300 switches using Cisco SFP-H10GB-CU3M DACs. After enabling allow-unsupported-transceiver the cables were still not recognised: show tech transceivers listed the port as unsupported, the LED…
We are standing up four DGX Spark nodes for disttributed training and hung them off a MikroTik CRS812-8DS-2DQ-2DDQ. The plan was one 400G QSFP-DD port on the switch feeding two nodes at 200G each, so a couple of breakout cables cover the whole cluster. MikroTik CRS812-8DS-2DQ-2DDQ, QSFP-DD ports…
Rebuilding aggregation at one of our sites: a CRS326-24S+2Q+RM takes the custmer SFP+ ports and uplinks over 40G into a Huawei S6720. Short run inside the same rack, so a passive DAC rather than optics. MikroTik CRS326-24S+2Q+RM, QSFP+ port qsfpplus1-1 Huawei S6720-54C-EI-48S-AC, plain 40GE port…
The poster tried to link an HPE FlexFabric 5900AF and a Dell S5212F-ON at 10 Gbps with DAC cables that had been custom-made with an HPE-coded end and a Dell-coded end. Both ports were forced to 10G full duplex, but no link came up. On the HPE side the interface reported Media type is stack wire…
Two Aruba 2930F switches (JL256A, firmware 16.05.0003) were to be stacked with VSF over an HPE DAC. With allow-unsupported-transceiver enabled the DAC passed traffic on normal ports, but as soon as the ports were made VSF member links the stack would not form. Replacing the DAC with supported 10G…
An HPE 2920 (J9729A, firmware WB.15.17.0009) with the J9731A 10G expansion module was connected to a DL380 Gen8 with a 560SFP+ NIC using a genuine HPE X242 3 m SFP+ DAC (J9283B). Port A1 with a J9150A SR module worked, but port A2 with the DAC logged Transceiver type not supported in this port and…
The poster needed to connect stacked Aruba 6300F (JL665A) switches to a 6300M core (JL658A) at 10 Gbps over more than 3 m. J9283D 3 m DACs worked for short runs and the older 3810/2930 platforms supported a 7 m J9285D cable, but that cable is not listed for the 6300. The question was whether the 5…
With an Aruba 2930F connected to a server through a Stornet-branded J9283D-SN passive 3 m SFP+ DAC, port 50 dropped the link immediately after it came up and port 52 flapped with the log message FFI : Port: 52 Excessive link state transitions. The same cable worked on ports 49 and 51, and fibre…
The poster wanted a cheap 10G link between servers with Intel X520-DA2 NICs and an HP switch and worried that a direct-attach cable is coded either for Intel or for HP but not both. A respondent shared that two X520-DA2 cards would not link directly over a DAC in their case, but a Dell DAC…
The poster, validating their product against Cisco Nexus 9000 switches (a Nexus C9332D-GX2B chassis), is blocked by bug CSCwo18785: configuring 200G on a QSFP-200G DAC fails with 'ERROR: The transceiver doesn't support this speed'. The cable is a Mellanox MCP1650-H002E26 200GbE DAC; connected…
