Popular discussions about programming, compatibility and testing of optical transceivers.
Before deployment the poster asked for a certified or tested SFP28 DAC to connect an HPE FlexFabric 5950 with an SFP28 card to a dual-port Mellanox MCX4121A-ACAT (ConnectX-4 Lx), and for any documentation of that pairing. Hardware involved: HPE FlexFabric 5950, Mellanox MCX4121A-ACAT, SFP28 DAC…
The poster runs a Cisco Nexus 5000 with an N2K-C2232PP-10GE fabric extender. Three FEX-facing ports report 'sfp validation failed' with Cisco FET-10G modules. Following advice found online, the module was removed, the port speed set to 1000 and the module reinserted; the port was also shut/no shut…
A QSFP112 400G SR4 module in a ConnectX-7 (MCX755106AC-HEAT) with an MPO-12 Type-B cable showed module state Ready and data path DPActivated, but mlxlink --showmodule reported State = Disable, Supported Cable Speed = 0x00000000, Compliance = Unspecified/Undefined, Power Class 1.5 W (too low for…
A DS14-MK4 shelf came my way for almost nothing and I would like to hang it off an ordinary tower server as bulk storage at home. It is fully populated with its original carriers, it powers up, fans spin, front panel looks alive - but I cannot get a single disk to appear on the host. NetApp…
After moving a Bell fibre connection from an ER-X to an ER-4 with the ISP's Alcatel-Lucent/Nokia GPON SFP (3FE46541AA / G-010S-P) plugged directly into eth3, the WAN dropped every 3 to 60 minutes; syslog had hundreds of kernel: Failed to read SFP EEPROM1 at byte 0 val -6!! entries and SFP module…
The poster wanted to use a QSFP+ 40G-to-4x10G breakout cable on a two-port Mellanox ConnectX-3 Pro (MT27520, firmware 2.42.5044, PSID HP1370110017, MLNX OFED 4.6 on Debian 9.6) so each 10G leg could connect to a different switch, similar to what an Intel XL710 offers. SR-IOV virtual functions had…
A Cisco Nexus 5672UP fitted with a 10GBASE-SR SFP+ could not connect to another switch that uses a 1000BASE-SX (1 Gbps) transceiver; both ends are multimode optics. When the poster changed the port speed, 'show interface brief' displayed an 'SFP checksum error', and swapping the Nexus optic for a 1…
A dual-port ConnectX-5 (MT27800, firmware 16.35.1012, MLNXOFED 5.8 on BC-Linux 8.2) connected to a switch with a DAC would not recover after the cable had been connected and disconnected about fifteen times: the port stayed in State: Polling with Physical state ETHANFSMABILITYDETECT, and mlxlink…
Four HP A5500-HI switches in an IRF stack logged unsupported transceiver messages for six rear-module (JD368B) ports that were cabled with HP J9281B SFP+ DACs to ProLiant Gen8 servers with 530SFP+ NICs. display transceiver interface shwed Transceiver Type STACKSFPPLUS, Connector COPPER, Vendor Name…
Across about forty ProCurve/Aruba switches the poster had used J4858C and J4858D 1G SX SFPs without issues, but eight newly purchased J4858D units logged Unsupported Transceiver on 2530-8G (J9774A, YA.15.16.0006), 2530-8G (J9777A, YA.15.12.0007) and 2530-24G (J9776A, YA.15.10.0003). show tech…
Small office, one leased line, and the carrier terminated it on an ADVA FSP150CP screwed to the wall of the comms cupboard. My job is to get our own router onto that circuit instead of renting one from them, so the ix0 SFP+ port of a Netgate XG-7100 goes straight ino the ADVA access port. Netgate…
We are adding capacity to a small FC fabric and bought compatible 16G short-wave SFP+ from an optics supplier instead of paying the switch vendor price. The switch refuses them. Brocade G610, Fabric OS 9.x generic-coded 16G SWL SFP+, correct wavelength and reach according to the label Brocade-coded…
We are adding a G610 to an existing fabric and there is a box of non-Brocade 16G/32G FC SFP+ left over from another build. Before I plan any ports around them I put one into a spare port on the bench to see what the switch makes of it. Brocade G610, Gen 6 third-party 32G FC SFP+, no Brocade…
Moving a pair of hypervisors onto Fibre Channel storage, and one host refuses to present a single LUN while the very same hardware works when the card is handed to a VM. QLogic QLE2692, ISP2722-based 16/32Gb FC, both ports cabled Fujitsu Eternus DX100 S5 at the other end Proxmox VE 6.2 host…
I run a ZTE ZXA10 C320 at a site, 10G uplink. I check levels and status by hand from the console, but I'd like to bring it all into monitoring so I don't have to jump into the CLI for every subscriber complaint. OLT: ZTE ZXA10 C320 uplink: SFP+ in xgei1/21/1 subscribers on gpon-onu1/1/1:1 and…
