A 1000BASE-T copper SFP (Arista SFP-1G-T) in an Arista switch does not link to a device that only rnus 100 Mbit/s, and a 10GBASE-T SFP+ does not fall back to a lower rate either. How does EOS handle speed negotiation for copper SFP modules?
A customer with a 10Gtek ASF-10G-T 10GBASE-T transceiver could not read its EEPROM: ethtool -m ens802f0 returned Cannot get module EEPROM information: Operation not supported. The vendor attributed it to a firmware version mismatch between the NIC and the transceiver. Hardware involved: 10G NIC…
A UCG-Fiber used a UACC-CM-RJ45-MG 10GBASE-T module (port 6, later port 7) to reach a Zyxel XS1930. Whenever the copper cable was disconnected for more than about 40 s or the Zyxel rebooted, the link never came back until the module was pulled for a minute or the gateway rebooted; forcing 10G or 1G…
A pfSense router on a Supermicro R210 II with an AOC-STGN-i2S (82599-based X520 clone) was connected throguh an FS.com SFP+-to-RJ45 module to a cable modem with a 2.5 Gbps port. No link negotiation happened; pfSense offered only auto and 10G speeds and never 2.5G. Hardware involved: Supermicro…
Home setup, everything in one rack. I want to connect the NAS to the switch faster than gigabit, but I don't want to run fiber: the distance is about five meters, a plain patch cord covers it. D-Link DGS-1250-28X switch, SFP+ ports free TerraMaster F4-424 Max NAS, copper RJ-45 port short Cat6a…
A Dell-branded Intel X520-DA2 with Flypro 10GBASE-T SFP+ modules showed no carrier (or no interface at all) on Debian and on FreeBSD-based OPNsense because the card rejects unapproved modules. The post collects the per-OS fixes and the permanent EEPROM approach. Hardware involved: Dell-branded…
I run a Turris Omnia NG at home and the last thing sitting on the metallic WAN port is a two metre hop to the ISP router. I would like to move that hop into the SFP+ cage and free the copper port for the lab side. The official Turris SFP+ copper module (RTROM01-RTSF-10G) costs about what a small…
A FreeNAS build on a Supermicro X11SPM-TPF board would not recognise a Ubiquiti UF-RJ45-10G SFP+ copper module in the on-board SFP+ cage, although the switch side showed link. The poster asked for BIOS settings or a compatible 10G RJ45 transceiver. Hardware involved: Supermicro X11SPM-TPF, Intel…
A QSFPTEK 10GBASE-T SFP+ module installed in port ix1 of a passively cooled Netgate 6100 reported 73 C through DDM although the room was at 20 C; the module is specified for 0-70 C and up to 2.5 W. The poster asked for known-good RJ45 SFP+ modules that stay within spec. Hardware involved: Netgate…
Small tower site: an RB4011 in a ventilated roadside cabinet feeding a couple of radios, with one 10GBASE-T copper hop over to the switch because there was already cable in the duct. The port drops out on warm afternoons and comes back at night, which points fairly clearly at the module rather than…
On a Minisforum MS-01 running Proxmox (i40e, kernel 6.8.12-10-pve) the X710 SFP+ port enp2s0f0np0 recogniesd a Ubiquiti SFP+-to-RJ45 module (ethtool listed 10G Base-SR capability) but the link never came up: Link detected: no, interface DOWN, no dmesg errors, ip link set up made no difference…
H3C-SFP-10G-T-SO 10GBASE-T copper modules (from FS or Solid Optics) worked out of the box in a FlexFabric 5940 (JH398A) with the JH181A 24-port SFP+ card, but in a FlexFabric 5945 (JQ076A) with the same card the ports only came up after manually running port up-mode on the interface. The poster…
I look after a small office network, one switch closet, and the four SFP+ cages on our access switch carry the 10G links to the server rack. It ran for months without a thought and now one cage is simply gone. TP-Link TL-SG3428X-M2 (V1), firmware 1.20.4 Build 20241104 Rel.40746, adopted in Omada…
We are consolidating a pair of R630s onto 10G and the cabling to the top of the rack is copper, so instead of pulling fibre I put 10GBASE-T SFP+ modules into the X520 cards. The switch end takes them without a word. The servers refuse to. Dell PowerEdge R630, Intel X520 (82599), dual port FS…
