Homelab, nothing exotic. An Odroid H2 does routing duty on its 2.5GbE ports, and I wanted to hang it off one of the 10GbE SFP+ cages of the switch through an RJ45 copper module instead of pulling fibre across the room. QNAP QSW-M408S, copper module in one of the 10GbE SFP+ cages Odroid H2 router…
Small office, two buildings, and all I want is a plaain 1000M fibre link between the racks. Both ends are configured for 1000M, both stay dark, and this has been dragging on for weeks now. TP-Link TL-SG3452P, hardware V3, firmware 3.20.4, link taken from one of its SFP cages PLANET IGS-6329-8UP2S4…
Small vSphere cluster, two 10G uplinks per host into a pair of top-of-rack switches. After the ToR was rebooted for a firmware update, part of the VMs on one host went silent and vMotion failed on both uplinks - yet ESXi never marked anything down and the adapter LEDs stayed lit the whole time…
We keep a couple of ONIE boxes in the lab rack for testing, and one of them is an Edgecore AS5114-48X-O-AC-F-EC running dentOS. Port 18 is supposed to carry a 10G link to a neighbouring switch and it simply refuses to cmoe up, even though the platform clearly sees the module. Switch: Edgecore…
Small home rack, one server and one switch. I replaced an XGS1250-12 with an XS1930-10 and the only thing that did not survive the swap is the server uplink. Zyxel XS1930-10, SFP+ port with media type set to DAC10G Asus XG-C100F in the server 10Gtek CAB-10GSFP-P5M, 5 m passive twinax, AWG26 a…
Setting up 10G between a server and a TP-Link switch, nothing exotic. The card shows up in the system, driver loads normally, but there's no link on the port at all - no errors, no negotiation attempts. server: Intel X710, four 10GbE SFP+ ports, firmware 9.140.76856 TP-Link switch, SFP+ port cable…
We pulled a pair of G8124E out of a decommissioned rack and I am rebuilding them as the aggregation layer for an internal test environment. Budget for branded optics is zero, so everything goes in with generic 10G SR modules of the type we already run elsewhere. Lenovo RackSwitch G8124E, ex-IBM…
My firewall is a Supermicro E300-9A running pfSense Plus 22.05, and both 10G SFP+ ports refuse to come up. Neither ix2 nor ix3 ever shows carrier, whatever I put in the cage. Hardware: Supermicro E300-9A, pfSense Plus 22.05 Ubiquiti DAC-SFP10-0.5M and a 10Gtek passive twinax cable Supermicro…
I inherited a Sun Network 10GbE Switch 72p with a couple of legacy boxes hanging off it that will never do more than a gigabit. The plan was to drop a 1G capable module into one of the SFP+ cages and be done with it. Sun Network 10GbE Switch 72p, SEFOS CLI over the serial console x2129a dual-rate…
Two Flex System enclosures, each with an EN4093R 10Gb Scalable Switch (option 49Y4270) as the network module. Ports come back error-disabled after a chassis power event, and less often drop into the same state while everything is running. It is not always the same ports, which is what makes this so…
I look after a small office network, one switch closet, and the four SFP+ cages on our access switch carry the 10G links to the server rack. It ran for months without a thought and now one cage is simply gone. TP-Link TL-SG3428X-M2 (V1), firmware 1.20.4 Build 20241104 Rel.40746, adopted in Omada…
Moving a pair of hypervisors onto Fibre Channel storage, and one host refuses to present a single LUN while the very same hardware works when the card is handed to a VM. QLogic QLE2692, ISP2722-based 16/32Gb FC, both ports cabled Fujitsu Eternus DX100 S5 at the other end Proxmox VE 6.2 host…
We took over a small aggregation site and one of the 10G uplinks has not come up since the module in it was swapped. The module is listed as incompatible with the CRS226, so that is where suspicion landed first, but the readings do not look like a rejected module to me. MikroTik CRS226 at the…
We are consolidating a pair of R630s onto 10G and the cabling to the top of the rack is copper, so instead of pulling fibre I put 10GBASE-T SFP+ modules into the X520 cards. The switch end takes them without a word. The servers refuse to. Dell PowerEdge R630, Intel X520 (82599), dual port FS…
A customer saw errors on a fibre link and suspected a speed mismatch with a 1G far end. The poster asked whether 10G SFP+ transceivers are backward compatible with 1G, or whether the modules had to be swapped for 1G SFPs to talk to the gigabit device on the other side. Hardware involved: Aruba…
